在廳門裝潢的領域里，我們有多種工藝可供選擇：從現代感的不銹鋼包覆，到色彩豐富的貼膜，再到經典耐用的噴漆工藝。然而，在這些方法中，不銹鋼包覆以其經濟性、美觀性以及耐用性脫穎而出，成為最受歡迎的選擇。您可能會好奇，這種不銹鋼包覆是如何做到既美觀又牢固的呢？是否存在脫落的隱患？為了解答這些疑問，今天，我們將帶您走進施工現場，一睹我們專業安裝師傅的精湛技藝，看看他們是如何將不銹鋼板巧妙地包覆在門上，確保其既美觀又安全。跟隨我們的腳步，一起見證廳門變身的過程，探索不銹鋼包覆背后的工藝秘密，讓您對廳門裝潢有更深的認識和了解。

　　In the field of hall door decoration, we have a variety of techniques to choose from: from modern stainless steel cladding, to colorful film coating, to classic and durable spray painting techniques. However, among these methods, stainless steel cladding stands out as the most popular choice due to its economy, aesthetics, and durability. You may be curious about how this stainless steel coating achieves both aesthetics and durability? Is there a risk of detachment? To answer these questions, today we will take you into the construction site to witness the exquisite skills of our professional installers, and see how they cleverly wrap stainless steel plates around doors to ensure both aesthetics and safety. Follow our footsteps and witness the transformation process of the hall door together, explore the secrets behind the stainless steel coating, and gain a deeper understanding and knowledge of hall door decoration.

　　01清潔準備

　　01 Cleaning Preparation

　　門板拆卸后，清除表面灰塵、臟污（如水泥、油污等），并去除保護膜，確保粘接面清潔，同時妥善保管鎖芯。

　　After disassembling the door panel, clean the surface dust and dirt (such as cement, oil stains, etc.), remove the protective film, ensure the bonding surface is clean, and properly store the lock cylinder.base64_image

　　02粘貼膠帶

　　02 Adhesive tape

　　在不銹鋼門皮或門基板上粘貼膠帶，上下兩端各兩條，間距約30mm；豎向膠帶間距為30-50mm，根據門板寬度適當調整，確保膠帶靠近邊緣。

　　Stick adhesive tape on the stainless steel door panel or door substrate, with two strips on each end at a distance of about 30mm; the vertical tape spacing is 30-50mm, adjusted appropriately according to the width of the door panel to ensure that the tape is close to the edge.

　　03撕除膠帶

　　03 Peel off the tape

　　撕去膠帶保護層，在間隙和接縫處均勻涂抹結構膠，避免過量造成鼓包。檢查膠帶，排除氣泡，確保貼合平整，尤其是鏡面材料，防止產生變形。

　　Tear off the protective layer of the tape and evenly apply structural adhesive to the gaps and seams to avoid excessive bulging. Check the tape, eliminate bubbles, ensure a smooth fit, especially for mirror materials, to prevent deformation.

　　04外包門板

　　04 Outsourced door panel

　　可選擇平放或豎放操作，確保不銹鋼門皮下端與門基板下端對齊，壓實邊緣后貼合表面。

　　You can choose to place it horizontally or vertically to ensure that the lower end of the stainless steel door skin is aligned with the lower end of the door base plate, and after compacting the edges, it fits the surface.

　　05清理表面

　　05 Cleaning the surface

　　粘貼完成后，用干凈抹布擦拭整個表面，以增強外包面板與基板的粘合，防止灰塵進入導致脫膠。

　　After pasting, wipe the entire surface with a clean cloth to enhance the adhesion between the outer panel and the substrate, and prevent dust from entering and causing delamination.

　　06精準打孔

　　06 Precise Drilling

　　確認外包面板與基板完全貼合后，開始精準打孔，并使用抽芯鉚釘加固，注意避免在可視面上打孔。

　　After confirming that the outsourcing panel is fully attached to the substrate, begin precise drilling and reinforce with pop rivets, taking care to avoid drilling on visible surfaces.

　　07沉孔處理

　　07 Sinking hole treatment

　　打孔后，使用較大鉆頭進行沉孔處理，及時清理孔內及孔周邊的鐵屑，然后使用抽芯鉚釘（沉頭鉚釘）固定。

　　After drilling, use a larger drill bit to sink the hole, clean the iron filings inside and around the hole in a timely manner, and then fix it with pop rivets (countersunk rivets).

　　08碰珠、鎖芯安裝

　　08 Installation of collision beads and lock cores

　　根據原門板的鎖孔和碰珠位置，精確開孔，注意保留原碰珠橡膠，鎖孔應為雙D型，避免使用過大的開孔器導致鎖芯安裝不穩。09清理、檢查及安裝

　　According to the lock hole and bead position of the original door panel, accurately drill the hole, and pay attention to retaining the original bead rubber. The lock hole should be double D-shaped to avoid using too large a hole opener that may cause unstable installation of the lock core. 09 Cleaning, Inspection, and Installation

　　最后清理所有鐵屑和污垢，檢查外包門板的安裝情況，確保所有輔助部件重新安裝到位，與拆門師傅協作完成門板安裝，結束外包工序。通過這一系列精細的工藝步驟，我們承諾為每一位客戶提供安全、美觀、耐用的電梯廳門包門解決方案。

　　Finally, clean all iron filings and dirt, check the installation of the outsourced door panels, ensure that all auxiliary components are reinstalled in place, collaborate with the door dismantling master to complete the door panel installation, and end the outsourcing process. Through this series of meticulous process steps, we promise to provide every customer with a safe, beautiful, and durable elevator hall door package solution.

　　本文由 濟寧電梯門套加工定制  友情奉獻.更多有關的知識請點擊  http://www.22-78.cn/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jining Elevator Door Frame Processing Customization For more related knowledge, please click http://www.22-78.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.